See where water runs, gathers and sits on your farm
A farm runoff map for any field, pasture or woodlot in Tennessee, traced from the USGS 3DEP lidar elevation model: the flow paths water takes across the ground, how many acres drain through each draw, the hollows where it sits after rain, which ground stays wet and how steep each slope is. Nothing to install and no account.
Use it to see where runoff concentrates before you walk the field, to look at the land uphill of your boundary that sends water onto it, and to take a map with the water on it to your soil conservation district or NRCS field office. You know where it runs after a storm; this shows how the pieces connect.
The workflow
Step 1 · Property
Load the farm boundary
The parcel from the state or county parcel map as the working area, or up to 25 parcels at once, or a box drawn around one field. Results on the map are clipped to it.
Step 2 · Water & Drainage
See where runoff gathers
Flow paths across the ground, each labeled with the acres of land draining through it, and a Ponding view of the low spots that would hold water, with depth, area and volume.
Step 3 · Downhill Path
Follow water from one spot
The line rain would run from a spot you click, such as a barnyard, a manure stack or the corner of a field, and how far it goes before it joins a water path or reaches a stream.
Step 4 · Catchment
See the land draining to a point
All the land upstream of a draw, a field corner or a stream crossing, in acres, including ground on the neighbor’s side of the fence and the road.
Step 5 · Wetness Map
Find the ground that stays wet
A map ranking the ground from dry ridges (tan) to the flats and hollows where the shape of the land concentrates water (blue).
Step 6 · Slope & Aspect
Read slope across the fields
Slope in degrees and percent for every part of the area, the share in each slope class, and how much is at any slope you type or steeper.
Step 7 · Point Elevation
Spot elevations for a tank, pump or ditch
The ground elevation in feet at up to 200 points you click, or on an even grid over a field.
Step 8 · Cut & Fill
Level a pad for a shed or barn
The cut and fill in cubic yards to level a pad at an elevation you set, or where the two balance.
Step 9 · Aerial History
Look back at the 2021 aerial photo
The 2021 USGS NAIP aerial photo of a spot, to swipe against today’s map: roads, ditches or a stream channel that have changed since.
Step 10 · Elevation Change
Compare two lidar surveys
Where two surveys of the same ground exist, where it dropped or rose between them, with the volume of ground lost and gained.
Step 11 · Property Report
Take it to your district or NRCS
A PDF terrain report for the parcel, and a data ZIP with contours, a slope map, flow paths, a wetness map and an aerial photo. Parcel boundaries are not included in the files; the outline of a box or area you draw is.
Free to run · pay to download
See the full result on the map free, with no account. Download flow paths as GeoJSON or KML, catchment outlines as DXF, GeoJSON or KML, slope and wetness grids as GeoTIFF, spot elevations as CSV, and the property report and its data ZIP with a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months, a one-off payment in US dollars that never renews. Every download on the site is included while the pass lasts.
What it doesn’t replace
- It maps where the ground sends water. It does not model erosion, sediment, nutrients, soil or how much rain it takes to start runoff.
- Tile drains, culverts, pipes and ditches narrower than the sampling are not in the terrain, so water is routed over the surface as if they were not there, unless you draw them under Culverts & barriers.
- It is not a conservation plan, a practice design or a wetland determination. NRCS offers conservation technical assistance that helps producers identify conservation objectives and a roadmap for conservation on their operation, and the local soil conservation district, found through the USDA service center for your county, works with landowners on conservation plans. Ask your district or NRCS field office what applies to your operation.
- The ground is as the lidar recorded it; leveling, ditching and terraces built since do not show. In Tennessee, USGS publishes lidar DEMs from two surveys of the same ground in parts of Nashville, Memphis, Chattanooga and Jackson. Many places have only one such survey so far.
- A large farm can exceed a tool’s area limit. Run it a field or a pasture at a time.
Questions
Can it show where runoff concentrates in a field?
Yes, that is what the flow paths show: the draws and swales where water from the ground above joins up, labeled with the acres draining through each. NRCS’s Grassed Waterway standard (Code 412) applies where concentrated surface flow needs added capacity and vegetation to prevent erosion. Whether a practice fits a spot, and how it would be built, is a question for your soil conservation district or NRCS field office, so take the maps to them.
Is this a conservation plan?
No. It is a set of terrain maps to bring to one: the boundary, the flow paths, the land draining to each draw, slope and wet ground. The plan, and any practice in it, comes from you and the people helping you.
Does it account for my tile drains and culverts?
Not unless you draw them. Under Culverts & barriers in Water & Drainage, Wetness Map and Catchment you can draw a culvert or drain the lidar can’t see, or a berm water has to go around. They are your assumption, and the results say when they were used.
Can several people use one pass?
A pass lives in the browser it was bought in, with no account. Anyone can run the tools for free; downloads work in the browser that holds the pass.
Guides
- Where Runoff Concentrates on Tennessee Farm Fields
- Terrain Checks Before Buying Rural Land in Tennessee
- Contour Map of Your Tennessee Property
Data
Everything runs on the USGS 3D Elevation Program (3DEP) bare-earth elevation model: lidar at 3.3 ft per pixel where it has been flown, and the 1/3 arc-second model, about 33 ft per pixel, elsewhere. Every result says how much of the area came from that coarser model.
USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. Tennessee parcel boundaries come from the county assessors of property, through the Comptroller’s Division of Property Assessments and county GIS offices, and are not legal surveys; the parcel disclaimer accompanies the selection. The Esri aerial basemap follows Esri’s terms and is display-only; downloadable aerial photos use USGS NAIP.