Terrain Checks Before Buying Rural Land in Tennessee
Seven things you can measure about rural land or acreage from your desk, free, before you spend money on the things you can't.
Rural due diligence has an expensive half and a free half, and most people start with the expensive one. Soil tests, a septic evaluation, well records, a survey and a title report all cost money and take weeks — and they are worth it on the right property. The trick is knowing which property that is.
The free half is terrain. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. The USGS 3D Elevation Program publishes the result as a public bare-earth model, 3.3 ft per pixel where lidar exists. That answers a surprising number of the questions that decide whether a piece of land works, from the loess plains of West Tennessee to the Blue Ridge — and it answers them before you make an offer rather than after.
Start with the property boundary
Search the address and click the parcel. Where the state or county parcel layer has it, every check below then runs on the parcel rather than a rectangle you dragged. In Knox, Shelby and Chester counties, draw the property instead.
Open the Property tool →The seven checks
Run them in this order. Each is quick, and the early ones will rule out properties before you bother with the later ones.
How much of it is actually usable
Listings quote acres. What matters is how many of those acres you can drive a tractor on, build on or graze. Map slope across the parcel to see where the steep ground lies, and use the property report for the share of the land in each slope band rather than the average — a parcel that is half flat bench and half steep face averages to a number that describes neither half.
Slope & aspect →Which way it faces
Aspect decides sun, afternoon heat, drying, growth and how a house feels in January and in August. Look at how much of the land faces south, and especially whether the flat, buildable ground is on a south face or a north one. It is the single most common thing buyers notice too late.
Slope & aspect →Where the water goes
Flow paths show where water crosses the property in heavy rain, and the catchment above a point shows how much land drains onto it. Flat ground at the bottom of a large catchment is flat for a reason. Pair this with the FEMA flood maps.
Water & drainage →Where water sits
Closed hollows — low points with no outlet — are where water ponds after rain. In a dry August they look like good flat pasture. Finding them before closing is far cheaper than finding them after the first big storm.
Water & drainage →The grade between road and house site
Draw a line from the road frontage to each possible building site and read the profile. It shows the access grade, whether gravity will carry services where they need to go, and roughly how much driveway you are paying for. A steady grade over a long driveway is a different proposition from the same rise packed into one short pinch.
Elevation profile →What the house would see
Put a point at each possible house site and run a viewshed to see what is visible from it — the hills, the creek, the neighbors — and just as usefully, what can see it. Moving a site a hundred feet along a contour often changes the outlook completely, and it is easier to test that now than after the foundation is poured.
Viewshed →Signs of past earthwork and instability
Generate fine contours and look at their shape. Unnaturally straight, evenly spaced lines usually mean cut and fill — an old pad, a farm road, a pond dam, a filled hollow. Hummocky, irregular contours on a slope can mean slumped or disturbed ground; a geotechnical engineer is the person to ask. Neither is necessarily a problem, but both are worth asking about.
Contour lines →To see the ground cover as well as the shape of the land, the Download Data tool delivers a georeferenced color aerial photo of the property from USGS NAIP (public domain), covering the parcel plus 100 ft on every side, ready to open in QGIS, ArcGIS or AutoCAD Civil 3D.
Check the data before you trust it
Two properties of the elevation data decide how much weight any of the above can carry, and both vary by place.
Resolution. Where a lidar work unit exists, all seven checks are reliable. Where it does not, the USGS model falls back to about 33 ft per pixel, and slope on gentle ground or fine drainage detail should not be trusted. Every Download Data file states what share of its area came from that fallback.
Age. The model shows the ground as it was when it was flown. Grading, clearing, new ponds, slides and river movement since then are invisible. If a listing mentions recent work, check the flight year before drawing conclusions from the contours.
Both are answered for a specific address on the lidar coverage page.
Put it in one document
The property report runs the whole set over a parcel and returns a multi-page PDF — hillshade, contours, slope and aspect breakdowns, elevation statistics and a checklist of the official records it does not cover.
What elevation data cannot tell you
Being clear about the limits is what makes the rest useful. The ground surface is one layer of a rural purchase, and there are several it cannot see. In Tennessee, these are the records to check:
- Assessment and deed records — the county assessor of property values and maps the parcel, and the county register of deeds records deeds and other documents. The Tennessee Comptroller's Division of Property Assessments supports most county assessors, and its Tennessee Property Assessment Data (TPAD) site looks up assessment records.
- Zoning and land use — zoning in Tennessee comes from the city or the county. Ask the planning office of the city or county where the land is what applies to it, including subdivision and floodplain rules. Deed restrictions can also limit what you build.
- Flood maps — elevation shows where water would go; FEMA's flood maps show the mapped flood hazard.
- Geology — the Tennessee Geological Survey in TDEC (the Tennessee Department of Environment and Conservation) publishes geologic maps and information for the state.
- Septic — subsurface sewage disposal systems are permitted through TDEC's Division of Water Resources (Ground Water Protection), or in some counties through a county health department working under contract with TDEC.
- Wetlands — the USFWS National Wetlands Inventory maps wetlands nationwide.
- Title, easements and access — a preliminary title report from a title company.
- Under the surface — soil type and depth, groundwater, wells, old fill and contamination are invisible in an elevation model.
Used properly, the terrain pass narrows a shortlist and sharpens the questions you take to the professionals, the city, the county and TDEC. It does not replace them.
Where the data comes from
Ground elevations come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model, with elevations above NAVD 88. Source cells are 3.3 ft per pixel in the finest work units, with about 9.8 ft per pixel and 33 ft per pixel sources elsewhere. USGS elevation data is public domain. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. Property boundaries come from the state’s parcel layer, published by the Tennessee Comptroller of the Treasury’s Division of Property Assessments through TNMap, in 86 counties, and from the county’s own GIS layer in Davidson, Hamilton, Hickman, Montgomery, Rutherford and Williamson counties. Parcel maps are not surveys, and Knox, Shelby and Chester counties have no parcel selection. You can do all of this yourself in QGIS from The National Map Downloader; this site saves you the download and the setup. More from the USGS 3D Elevation Program and Tennessee elevation and lidar resources.
Related guides
- Slope maps for building on sloping land — steepness bands, aspect and what to ask the city or county.
- Contour map of your property — contours over the parcel from the state or county parcel map.
- Lidar coverage in Tennessee — resolution and flight year for any address.
- Elevation lookup — ground elevation at a single point.
- Download DEM data for Tennessee — if you would rather run the analysis yourself.
Frequently asked questions
What should I check about the land before buying acreage in Tennessee?
Before paying for professional reports, there are seven things you can measure from public elevation data: how much of the land is workable rather than steep, which way it faces, where water flows across it, where it ponds, the grade between the road and a possible house site, what a house would see, and whether the ground shows signs of past earthwork or sliding. All of them come from the USGS 3DEP lidar elevation model, which is public.
How can I tell if rural land floods?
Elevation data will not tell you that a property has flooded, but it shows where water goes, which is the physical reason it might. Run the drainage tool to see flow paths across the land and look for closed hollows where water collects. Then check the FEMA flood maps and ask the city or county floodplain administrator. Elevation shows the mechanism; the official maps and records show the history.
Does aspect really matter when buying rural land?
A great deal, and it is a common regret. In Tennessee, as anywhere in the northern hemisphere, a south-facing slope gets the most sun: it dries out sooner and takes the full heat of the afternoon, which is welcome in a winter garden and hard on a summer one. A north-facing slope of the same steepness stays cooler and holds moisture longer, and in the short days around December 21 it may see much less direct sun. Two properties a mile apart at the same price can be very different places to live and farm.
How steep is too steep?
It depends on what you want to do, and no single number answers it. The property report splits a parcel into four slope bands — under 10°, 10–20°, 20–25° and over 25° — and gives the share of the land in each. Gentle ground is where fields, building pads and driveways come easiest, and each step up asks more of the design and the earthwork. These are not legal thresholds — check with the city or county for zoning and subdivision rules, and with TDEC or the county health department for septic. The useful figure is not the average slope but the share of the land in each band.
Can I check all this before making an offer?
Yes, and that is the point of doing it first. Slope, aspect, drainage, access grade and views can all be measured from your desk in an afternoon from public data. Soil tests, geotechnical reports, surveys and title work cost money and time. Running the terrain checks first tells you which properties are worth paying to investigate, and gives you specific questions for the listing agent and the seller.
How old is the elevation data, and does that matter?
It varies by place: each area was flown by a particular lidar project in a particular year. It matters for anything recent — a pad cut, a new pond, a farm road or a slide after the flight will not appear. Check the project and year for the property on the lidar coverage page before drawing conclusions about earthwork.
Is this a substitute for professional due diligence?
No. It is the free first layer. Elevation data cannot see soil, groundwater, wells, septic suitability, zoning or deed restrictions, easements, title or wetlands — all of which can decide whether a rural purchase works. Use it to shortlist and to arrive at the professionals, the city, the county and TDEC with better questions.