Download DEM Data for Tennessee: A Guide to Digital Elevation Models

Where Tennessee's digital elevation models come from, how to download them, and how to get processed elevation results straight away without GIS software or raw file handling.

Need elevation data without the hassle?

Clip a GeoTIFF of exactly your area, or skip the raster and go straight to contours, profiles or enriched files from the same USGS 3DEP lidar.

Use DEM data now →

What is a digital elevation model (DEM)?

A digital elevation model is a regular grid of elevation values. Each cell holds one height, and together the cells describe the shape of the land. DEMs underpin flood modeling, viewsheds, slope analysis and contour generation.

Open one in QGIS or ArcGIS and you see a grayscale image where brighter cells are higher. The resolution is the size of each cell on the ground: a DEM at 3.3 ft per pixel has cells 3.3 ft on a side.

DEMs are usually stored as GeoTIFF or Cloud Optimized GeoTIFF, which carry the coordinate system and extent in the file so GIS software can place the grid correctly on a map.

DEM, DSM and DTM: the differences

Digital surface model (DSM)

The highest surface at each point: tree crowns, roofs, power lines. On a wooded slope in the Great Smoky Mountains a DSM shows the canopy, not the ground under it. Surface models are used for line of sight and shade. This site has no surface model, so every tool on it uses bare earth.

Digital terrain model (DTM)

The bare ground with vegetation and buildings removed, made by keeping only the lidar returns classified as ground. It is the right model for drainage, slope, contours and earthwork.

DEM as an umbrella term

“DEM” is sometimes used for both and sometimes for the bare-earth model alone. The USGS 3DEP seamless DEM is bare earth. For contours, profiles and slope, bare earth is what you want.

Tennessee DEM sources

USGS 3DEP lidar DEM (highest resolution)

Ground elevations come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model, with elevations above NAVD 88. Source cells are 3.3 ft per pixel in the finest work units, with about 9.8 ft per pixel and 33 ft per pixel sources elsewhere. USGS elevation data is public domain. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. Values in the downloaded file are in meters, as USGS publishes them. See the lidar data guide for how it was flown. More from the USGS 3D Elevation Program and Tennessee elevation and lidar resources.

USGS 3DEP 1/3 arc-second

Where no lidar work unit meets the USGS standard for its finest DEM, the seamless 3DEP model uses coarser data, down to 1/3 arc-second, about 33 ft per pixel. That covers everything, and it is far coarser: fine for a regional picture, not for site work.

Tennessee Elevation/LiDAR Program

The Tennessee Elevation/LiDAR Program site is linked from the state's STS GIS office. Read each dataset's metadata for its date, units and coordinate system.

Global satellite models

Global elevation models from satellite missions cover the whole planet at roughly 100 ft per cell or coarser and often record the top of the forest rather than the ground. In Tennessee the 3DEP model is far more detailed.

How to download raw DEM data

  1. Open The National Map Downloader. The National Map Downloader is USGS's download tool for 3DEP products.
  2. Mark your area. Draw or search for the area you need on its map.
  3. Choose the elevation product. Pick the lidar DEM where it exists, or the 1/3 arc-second seamless model for wider coverage. Check each product's metadata for its resolution, coordinate system and date.
  4. Download the tiles. Data comes as tiles; you may need several to cover your area, and you merge and clip them yourself.
  5. Or request exactly your area. The 3DEP elevation image service can export a GeoTIFF of any bounding box directly, which is how this site reads it.

That gets you the raw data. Turning it into contours, profiles or enriched files still takes GIS skills — or a shortcut through this site.

Working with DEM files

GeoTIFF

A GeoTIFF is a TIFF image with geospatial metadata embedded: coordinate system, extent and cell size. Each cell holds a floating-point elevation rather than a color. High-resolution DEMs get large quickly: a lidar DEM of a block a few miles on a side runs to tens of millions of cells.

Coordinate systems and units

Tennessee data comes in several systems. USGS publishes 3DEP elevations in meters above NAVD 88. Tennessee survey and CAD work usually uses Tennessee State Plane, one zone for the whole state, in US survey feet. This site's DXF contours use Tennessee State Plane, US survey feet. Keep track of horizontal and vertical units separately: a metric DEM draped on a drawing in feet is the classic mistake.

Software

  • QGIS: free and open source; opens GeoTIFF, makes contours, hillshade and slope. Powerful, with a learning curve.
  • GDAL: the command-line toolkit behind most GIS software — gdalinfo, gdalwarp and gdal_contour do most DEM jobs.
  • ArcGIS Pro: Esri's commercial package with full surface analysis and 3D tools.
  • Global Mapper: a commercial package known for straightforward raster handling and contouring.

Why download raw files when you can get results straight away?

Tennessee Elevation Tools reads the USGS 3DEP model for you: contour maps, elevation profiles and enriched data files in seconds, with no GIS software.

The easy alternative: Tennessee Elevation Tools

Downloading and processing raw DEMs is powerful but slow: find the right product, choose coordinate systems, download large files, install GIS software and learn it before you get the answer you came for. Tennessee Elevation Tools delivers the most common DEM-derived outputs directly, with no account and nothing to install.

The DEM itself

The Download Data tool exports a GeoTIFF of the area you select, above NAVD 88 on a WGS84 latitude/longitude grid; values in the file are in meters, as USGS publishes them. Output resolution scales with the size of the area you select. Exports are capped at 1,024 pixels on the longest side, with a floor of 3.3 ft per pixel — so a 900 ft building site is delivered at the full lidar detail, while a block 7.5 miles on a side is resampled to roughly 39 ft per pixel. 3D DXF and LandXML surfaces keep the full lidar detail up to 0.6 miles per side and are thinned above that; the download panel shows their detail, point and triangle counts and the largest the file can be. Select a smaller area when you need fine detail.

The same Download Data tool also delivers a georeferenced color aerial photo of the area from USGS NAIP, which is public domain: a JPEG with a world file and projection file that lands in place under the DEM in QGIS, ArcGIS or Civil 3D.

Contour lines from the DEM

Draw an area, choose an interval and download contours as GeoJSON for GIS, DXF for CAD, PDF for print and more. See the contour lines guide.

Elevation profiles

Draw or tap out a line on the map and get an elevation chart, total climb and descent, and grade. See the elevation profile generator.

Adding elevation to files

Upload a CSV with latitude and longitude, or a GPX, KML or GeoJSON file, and download it with ground elevation added from 3DEP — no point-sampling workflow in GIS.

Common uses for DEM data

Flood and hazard assessment

Fine DEMs show flow paths, low spots and the ground a flood would reach. They complement the official flood maps from FEMA; they do not replace them.

Viewsheds and line of sight

A viewshed uses a DEM to find what can be seen from a point — for an antenna, a house site or a view across a river valley. A bare-earth viewshed leaves out trees and buildings, so it shows what the land itself allows; anything standing on it can only block more.

Slope and aspect

Slope is steepness; aspect is the direction a slope faces. In Tennessee, south-facing slopes get the most sun, which matters for solar, gardens, and how hot or dry the ground runs in summer.

Cut and fill

Comparing the existing ground with a level pad gives the volume of earth to move, in cubic yards. See the Cut & Fill tool.

Drainage and watersheds

Flow direction and accumulation from a DEM trace stream networks and watersheds, and show where water collects — essential for siting a house, a pond or a septic system.

Comparing the sources

SourceResolutionTypeUnitsCoverage
USGS 3DEP lidar DEM3.3 ft per pixelBare earthMeters, NAVD 88Where a lidar work unit meets the USGS standard for its finest DEM
USGS 3DEP 1/3 arc-secondAbout 33 ft per pixelBare earthMeters, NAVD 88Seamless
Tennessee Elevation/LiDAR ProgramVaries by projectElevation and lidar program data; check what each dataset holdsVaries; check the metadataProject by project

For most work in Tennessee the 3DEP lidar model is the right choice. The 1/3 arc-second model fills the gaps for regional work.

Licensing and credit

USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. Tennessee parcel boundaries come from the county assessors of property, through the Comptroller’s Division of Property Assessments and county GIS offices, and are not legal surveys; the parcel disclaimer accompanies the selection. The Esri aerial basemap follows Esri’s terms and is display-only; downloadable aerial photos use USGS NAIP.

Frequently asked questions

What is the best DEM source for Tennessee?

The USGS 3DEP seamless bare-earth model: 3.3 ft per pixel wherever a lidar work unit meets the USGS standard for its finest DEM, and coarser data, down to about 33 ft per pixel, elsewhere. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. It is free and in the public domain. The Tennessee Elevation/LiDAR Program site is the other place to look.

Do I need GIS software to use DEM data?

For raw GeoTIFF files, yes: QGIS, ArcGIS Pro or a similar package. Tennessee Elevation Tools reads the DEM for you and returns contour lines, elevation profiles and elevation-enriched files in the browser.

What format should I download a DEM in?

GeoTIFF is the most widely supported format and the right default. Cloud Optimized GeoTIFF (COG) is a variant that streams and reads partially, which helps with large areas. Every major GIS package opens both.

How do I make contour lines from a DEM?

In GIS software, use a contour tool (GDAL’s gdal_contour or the QGIS Contour algorithm) at the interval you want. Or let Tennessee Elevation Tools do it: select an area, choose an interval from 1 ft upward and download GeoJSON, DXF, PDF or another format.

What units and coordinate systems does Tennessee elevation data use?

USGS publishes 3DEP elevations in meters above NAVD 88. Lidar products from other sources may use Tennessee State Plane or UTM, in feet or metric units; check each product’s metadata. The GeoTIFF this site exports is on a WGS84 latitude/longitude grid, above NAVD 88; values in the file are in meters, as USGS publishes them. Its contour files carry feet, and its DXF contours are in Tennessee State Plane, US survey feet, the single State Plane zone that covers all of Tennessee. Make sure your project uses the same system as your data, and convert between metric and US units deliberately.

Is Tennessee DEM data free to use?

USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. Tennessee parcel boundaries come from the county assessors of property, through the Comptroller’s Division of Property Assessments and county GIS offices, and are not legal surveys; the parcel disclaimer accompanies the selection. The Esri aerial basemap follows Esri’s terms and is display-only; downloadable aerial photos use USGS NAIP. On this site every tool is free to use on the map; downloading the results needs a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months.

Data sources and further reading

This guide describes where Tennessee DEM data comes from; these are the places to get it. All of it is public and free to use.

Primary sources

  • USGS 3D Elevation Program (3DEP) seamless DEM — The bare-earth source for terrain tiles, contours, profiles, statistics, downloads and elevation added to files. Source resolution varies: 3.3 ft per pixel in the finest work units, with older lidar and coarser seamless data elsewhere. Elevations are above NAVD 88. Public domain. Selecting a fine output grid cannot create detail missing from the source.
  • Tennessee Elevation/LiDAR Program — The state’s lidar program and downloads for Tennessee. This site uses the USGS 3DEP index for work-unit coverage and available project metadata; it does not infer an acquisition date or accuracy for all of Tennessee from one project.
  • Tennessee Comptroller of the Treasury, Division of Property Assessments: parcel data — Parcel boundaries for 86 of Tennessee’s 95 counties, published through TNMap; the Property tool queries that public layer, and six counties’ own layers (Davidson, Hamilton, Hickman, Montgomery, Rutherford and Williamson). Knox, Shelby and Chester counties have no parcel layer on this site: draw the area there instead. Local gaps, outdated boundaries and missing parcel IDs can occur; no parcel found is not proof that land is unowned. Parcel maps are not legal surveys.
  • USGS Geographic Names Information System (GNIS) — Tennessee place names for search, including towns, peaks, lakes, streams and other named features.
  • Basemaps — USGS Topo and Esri World Imagery — USGS Topo, shaded relief rendered from 3DEP, and Esri World Imagery (Imagery: Esri, Maxar, Earthstar Geographics, and the GIS User Community) provide map context. The aerial basemap is display-only. Downloadable aerial photos come from public-domain USGS NAIP imagery.

Search, basemaps and terms

Related guides