Terrain · Click points, or choose an area for a grid
Find the ground elevation at any point in Tennessee
Point Elevation was formerly called Add Elevation.
Get the elevation at a point in Tennessee: click the map and each point is added to a numbered list with its ground elevation in feet, from the USGS 3DEP elevation model.
Point Elevation was formerly called Add Elevation. Click as many points as you need for a floor level, a water tank, a pump or a survey check, or switch to a grid of spot elevations over a lot, up to 50,000 points at 5, 10, 25 or 50 ft or a spacing you type from 2 to 3,000 ft.
Free to run · pay to download
See the full result on the map free, with no account. Download the point list or grid as CSV, GeoJSON or DXF with a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months, a one-off payment in US dollars that never renews. Every download on the site is included while the pass lasts.
Who uses this
- Owners and plumbers. Work out the fall from a tank or a well to the house.
- Surveyors. Sanity-check an elevation against the USGS model.
- Designers and drafters. Drop a grid of spot elevations into CAD as points in Tennessee State Plane, US survey feet.
When to use it
- You need spot elevations for a floor level, a water tank, a pump or a survey check.
- You want the elevation difference between a few places on a site, written down point by point.
- You need a grid of spot elevations over a lot for a drawing or a spreadsheet.
Tools for your job
Point Elevation is one step in a bigger question. These are the jobs it helps with, and the tools that go with it.
For the job: Plans, CAD, GIS and 3D printing
I need the terrain as a file.
- 1.Download Data — Contours, a GeoTIFF elevation model, a 3D DXF or LandXML ground surface, a georeferenced aerial photo or a 3D mesh for printing.
- 2.Data Here — Which USGS lidar surveys cover a spot, when each was flown, and where to get its files.
- 3.Elevation Change — Where USGS lidar was flown twice: whether the ground has slid, been filled or been cut between the surveys, as a GeoTIFF.
- 4.Contour Lines — Contours previewed on the map before you export them.
- 5.Elevate a File — Adds ground elevation to your own GPX, KML, GeoJSON or CSV points.
- 6.Point Elevation (this tool) — Spot elevations at the points you click or on a grid over a lot, as CSV, GeoJSON or DXF.
- 7.Terrain Stats — The highest, lowest and mean ground elevation of an area, and how the land is spread between them.
How to use it
- Open Point Elevation and click the map. Each click adds a numbered point (P1, P2, …) to the list and a numbered marker on the map.
- Click as many places as you like, up to 200. Remove one with its ×, or Clear all to start again; numbers are not reused until you clear the list.
- For a grid, switch to Grid in an area, choose a parcel, box, polygon or uploaded boundary, and pick a spacing (5, 10, 25 or 50 ft, or type one from 2 to 3,000 ft). The panel counts the points first; a grid holds up to 50,000.
- Download the list or the grid as CSV, GeoJSON or DXF (needs a pass). The list survives panning, zooming and switching tools.
Step by step: Cades Cove
We read spot elevations on Rich Mountain, above Cades Cove, with Point Elevation.
1.Open Point Elevation and click anywhere. Each click adds a numbered point to the list.
2.The panel shows each point’s ground elevation in feet above NAVD 88, its coordinates and the cell size it was read at. Click again to add another point, then download the list.
What it showed
- For spot elevations over a whole lot, switch to Grid in an area and choose a spacing.
- For a line of elevations, use Elevation Profile; for a whole file of points, use Elevate a File.
How it works
Each point is read from the USGS 3DEP bare-earth terrain tiles at about 6.3–6.4 ft cells, interpolating between the four nearest cells so the value is not snapped to a grid.
A grid is laid in Tennessee State Plane, US survey feet (EPSG:2274, one zone for the whole state) from the area’s south-west corner at the spacing you choose, keeping the points inside the area (and on its edge). Each point is read the same way as a click.
Reading the results
Feet above NAVD 88, which is close to mean sea level. Compare with a survey benchmark before using it for design elevations.
Each point lists its longitude and latitude, its X and Y in Tennessee State Plane, US survey feet (EPSG:2274, named in the file), and the cell size it was read at. X and Y are converted from the WGS 84 position with no datum shift, so they can sit about 3.0 ft to 3.6 ft from a NAD83 survey drawing. They are State Plane grid coordinates, with no surface adjustment factor applied.
The CSV and GeoJSON hold elevation_ft with an elevation_m column alongside; the DXF puts a point at each elevation, in US survey feet with a local origin, and a text label beside it.
Limits and caveats
- The panel shows the cell size read, not whether a height came from lidar. Outside the finest lidar work units, 3DEP can use older lidar at about 9.8 ft per pixel or a coarser model at about 33 ft per pixel, which is not fit for site-scale decisions. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown.
- Bare ground only. On a deck or a roof the value is the ground beneath it.
- Elevations are an estimate from a terrain model, not a survey. Where 3DEP has no data the terrain tiles hold 0, so a point there reads zero and is flagged in the list as a gap, not a ground height. Outside the area the tiles cover, a point is listed with no elevation and the reason.
- A grid spacing finer than the cells read adds interpolated points, not detail; the panel says when that happens. Larger areas are read from coarser tiles.
Data and attribution
Elevations come from the terrain tiles every map tool reads: the USGS 3DEP bare-earth model, served as Terrarium tiles and read at about 6.3–6.4 ft cells, the size the panel shows for each point. Elevations are above NAVD 88. Where 3DEP has no data the tiles hold 0, which is not a height; they hold no lake-bed depths.
USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. Tennessee parcel boundaries come from the county assessors of property, through the Comptroller’s Division of Property Assessments and county GIS offices, and are not legal surveys; the parcel disclaimer accompanies the selection. The Esri aerial basemap follows Esri’s terms and is display-only; downloadable aerial photos use USGS NAIP.
Questions
Is this elevation above sea level?
It is feet above NAVD 88, the national vertical datum, which is close to mean sea level. Compare with a benchmark before using it for design elevations.
What is in the download?
The point list or grid as CSV (longitude and latitude plus Tennessee State Plane, US survey feet X and Y), GeoJSON points with elevation, or a DXF with a point and a text label at each elevation, in US survey feet with a local origin. Each file states its coordinate systems, the vertical datum and the source.
Will the X and Y line up with my survey drawing?
Closely, not exactly. X and Y are converted from the WGS 84 position with no datum shift, so they can sit about 3.0 ft to 3.6 ft from a NAD83 drawing, and they are State Plane grid coordinates, with no surface adjustment factor applied. The files say so.
Ready to try it?
Open Point Elevation on the map →Free to use, no account. The analysis runs in your browser on public-domain USGS 3DEP data. Downloading the results needs a pass: see pricing.
Missing something you need? Suggest a feature or ask about custom work.