Lines · Draw or tap out a line

Elevation profile and grade along any line

Draw a line anywhere in Tennessee and get its elevation profile: distance, total climb and descent, and the grade section by section. It works as a driveway grade calculator, a trail grade check and a fall check for a ditch or a pipe run.

Your city, county or fire department sets the steepest grade a driveway may have. The profile shows exactly which stretch exceeds the number you are working to.

Free to run · pay to download

See the full result on the map free, with no account. Download the profile as CSV, 3D GeoJSON, KML or a 3D DXF with a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months, a one-off payment in US dollars that never renews. Every download on the site is included while the pass lasts.

Who uses this

  • Owners and designers. Check a driveway or a path meets the grade before it is drawn up.
  • Farmers and ranchers. Test a farm road, a lane or a fence line.
  • Hikers, runners and riders. Get the climb on a route.

When to use it

  • Planning a driveway, a farm road, a pipe run or a fence line.
  • Checking the climb on a hike, a ride or a run.
  • Seeing whether water will flow the right way along a proposed ditch.

Tools for your job

Elevation Profile is one step in a bigger question. These are the jobs it helps with, and the tools that go with it.

For the job: Excavation, driveways and farm roads

How much digging, and can a driveway or farm road make the grade?

  1. 1.Cut & Fill — Cut and fill in cubic yards to level a pad, at an elevation you set or the one that balances.
  2. 2.Elevation Profile (this tool) — Grade along a proposed driveway, section by section.
  3. 3.Route Explorer — Finds a line between two points that stays under a maximum grade.
  4. 4.Contour Lines — Site contours at 1 or 2 ft to hand to a designer.

For the job: Hikes, runs and rides

How much climbing, and how far?

  1. 1.Elevation Profile (this tool) — Distance, total climb and descent, and the steep sections.
  2. 2.Elevate a File — Replaces the noisy altitude in a GPX from a watch or phone with lidar ground elevation.
  3. 3.Measure — A quick flat distance between points.

How to use it

  1. Open Elevation Profile and tap out the line, corner by corner. Undo removes the last point.
  2. Finish the line. The profile chart appears in the panel.
  3. Hover, tap or drag along the chart to read distance, elevation, gradient and position at any point; a marker follows on the map. Pointing at the line on the map moves the chart too, and with the chart selected the arrow keys step along it.
  4. With a pass, download the profile as CSV, 3D GeoJSON or KML (WGS 84), or a 3D DXF polyline (Tennessee State Plane, US survey feet). Saving a picture of the chart is free.

Step by step: Cades Cove

We draw a cross-section from the floor of Cades Cove up the slope toward Rich Mountain, to the north.

1.Open Elevation Profile and tap out the line, corner by corner. Choose Done.

2.The panel gives the length of the line, the total climb and descent, and the lowest and highest points.

What it showed

  • Hover, tap or drag along the chart to read distance, elevation and gradient at any point; a marker follows on the map. With a pass, download the profile as CSV, 3D GeoJSON, KML or DXF.

How it works

The line is sampled at close, even spacing, plus every corner you placed, and the USGS 3DEP bare-earth model is read at each sample, interpolating between cells. Ascent and descent ignore ups and downs of less than 6.6 ft along the way, so terrain-model noise does not inflate the totals; whatever is still climbing or falling at the end of the line is counted, so ascent minus descent always equals the change from start to finish. Gradient at a point is rise over run between the samples either side of it.

Reading the results

Gradient is in percent: 10% is 1 ft of rise for every 10 ft along. Your county or city sets the maximum grade for a driveway; check its standards before designing to a number.

Total ascent and descent add up every climb and drop of 6.6 ft or more, so a rolling line shows more climb than the difference between its ends. Smaller wiggles are treated as terrain-model noise.

The CSV has one row per point: distance, coordinates in WGS 84 and Tennessee State Plane, elevation and gradient, with the source and datum on every row. The DXF is a 3D polyline in US survey feet, at full coordinates or shifted near 0,0.

Limits and caveats

  • Lines up to 15.5 miles.
  • Outside the finest lidar work units, 3DEP can use older lidar at about 9.8 ft per pixel or a coarser model at about 33 ft per pixel. Fine output spacing cannot recover missing source detail. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown.
  • Bare ground only. A bridge or a culvert shows as the valley beneath it.

Data and attribution

Results come from the USGS 3D Elevation Program (3DEP) bare-earth elevation model: lidar at 3.3 ft per pixel where it has been flown, with older lidar at about 9.8 ft per pixel and coarser sources at about 33 ft per pixel elsewhere, with elevations above NAVD 88. Every tool is bare earth: trees and buildings are not in the elevation model for Tennessee, so Sunlight, Viewshed and Sightline work from the terrain alone.

USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. Tennessee parcel boundaries come from the county assessors of property, through the Comptroller’s Division of Property Assessments and county GIS offices, and are not legal surveys; the parcel disclaimer accompanies the selection. The Esri aerial basemap follows Esri’s terms and is display-only; downloadable aerial photos use USGS NAIP.

Questions

What is the maximum driveway grade in Tennessee?

Check the driveway and emergency-access standards that apply to your actual location and project with the relevant local planning or public works office. The terrain model does not determine compliance.

Ready to try it?

Open Elevation Profile on the map →

Free to use, no account. The analysis runs in your browser on public-domain USGS 3DEP data. Downloading the results needs a pass: see pricing.

Missing something you need? Suggest a feature or ask about custom work.