Data · Select an area up to 1.24 mi across

See how the ground has changed between two lidar surveys

Lidar change detection for Tennessee, free on the map: where USGS publishes lidar from two surveys of the same ground, compare them and see where it dropped or rose between them: landslides, grading, fill, river banks and gravel bars.

Choose an area up to 1.24 mi across and the two surveys. The map shades loss red and gain blue at the full lidar detail, and the panel gives the volume of ground lost and gained in cubic yards, leaving out differences small enough to be survey noise.

Free to run · pay to download

See the full result on the map free, with no account. Download a GeoTIFF of the change on the surveys’ own 3.3 ft grid in NAD83 / UTM, naming both surveys and their years with a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months, a one-off payment in US dollars that never renews. Every download on the site is included while the pass lasts.

Who uses this

  • Buyers and owners. Check whether a property has slid, been filled or been cut between two surveys.
  • Engineers and geologists. Get a first look at landslide volumes and deposition before ordering a survey.
  • GIS analysts. Download the change as a GeoTIFF on the surveys’ own grid, with both surveys named in the file.

When to use it

  • You want to see what a landslide, flood or storm did to the ground between two surveys.
  • You want to know whether a site has been filled, cut or graded since an earlier survey.
  • You want to see how far a river bank, gravel bar or bluff has built up or worn away.

Tools for your job

Elevation Change is one step in a bigger question. These are the jobs it helps with, and the tools that go with it.

For the job: Plans, CAD, GIS and 3D printing

I need the terrain as a file.

  1. 1.Download Data — Contours, a GeoTIFF elevation model, a 3D DXF or LandXML ground surface, a georeferenced aerial photo or a 3D mesh for printing.
  2. 2.Data Here — Which USGS lidar surveys cover a spot, when each was flown, and where to get its files.
  3. 3.Elevation Change (this tool) — Where USGS lidar was flown twice: whether the ground has slid, been filled or been cut between the surveys, as a GeoTIFF.
  4. 4.Contour Lines — Contours previewed on the map before you export them.
  5. 5.Elevate a File — Adds ground elevation to your own GPX, KML, GeoJSON or CSV points.
  6. 6.Point Elevation — Spot elevations at the points you click or on a grid over a lot, as CSV, GeoJSON or DXF.
  7. 7.Terrain Stats — The highest, lowest and mean ground elevation of an area, and how the land is spread between them.

How to use it

  1. Open Elevation Change and frame the area on the map, draw a box, or select a parcel with the Property tool. Areas can be up to 1.24 mi across.
  2. The panel lists the lidar surveys with a published 3.3 ft lidar DEM that cover the area, and picks the oldest and newest. Change either one for a different pair.
  3. Choose Compare surveys. Red shows where the ground went down, blue where it went up, and the panel gives the volumes.
  4. Choose Before & after photos to swipe between two years of aerial photos either side of a divider on the map: the panel picks a photo from before the earlier survey and one from after the later survey, and either can be changed. The change colors can be laid on top.

Step by step: a Nashville neighborhood

We compare two lidar surveys of the same ground in Nashville, where USGS publishes lidar from more than one survey.

1.Open Elevation Change and frame the area. The panel lists the lidar surveys with a published lidar DEM that cover it, oldest and newest picked. Choose Compare surveys.

2.Blue is ground that rose, red is ground that dropped. The panel gives the volumes lost and gained, the biggest drop and rise, and how much of the area both surveys cover.

3.Choose Before & after photos to see aerial imagery either side of a divider on the map. Drag the handle, or switch the change colors on or off.

What it showed

  • Broad, consistent patches of color are change; speckle under dense vegetation and single-spot jumps are usually survey noise.
  • If the whole area reads a little higher or lower, the panel says so: that is often an offset between the two surveys.

How it works

Both surveys’ 3.3 ft lidar DEMs are read for the area straight from the USGS files, which hold each survey on the same 3.3 ft grid in NAD83 / UTM (whichever zone the surveys’ files for the area are in; Tennessee spans zones 15N to 17N) with heights above NAVD 88, so each cell is compared with the same cell, with no resampling. The surveys come from the USGS 3DEP index; their years come from its collection dates, not from survey names.

Each cell’s change is the later height minus the earlier one. Changes smaller than ±1 ft are treated as survey noise and left out of the totals and the colors. Volumes add up the change in every remaining cell.

Reading the results

Red is lower in the later survey, blue is higher. The color is darkest at the change shown under the color bar; bigger changes are the same color.

Ground lost and gained are separate totals, so a landslide that moved earth downhill shows both: a red scar and a blue deposit.

If the whole area reads higher or lower, the panel says by how much. That can be real, or an offset between the two surveys; the panel names the geoid models when the surveys were processed with different ones.

A large jump at a single spot can be a difference in how each survey classified the ground, not a real change. Trust broad, consistent patches.

Limits and caveats

  • Only where USGS publishes a 3.3 ft lidar DEM from two surveys of the same ground. In Tennessee, USGS publishes lidar DEMs from two surveys of the same ground in parts of Nashville, Memphis, Chattanooga and Jackson. Many places have only one such survey so far. Data Here shows which surveys cover a spot.
  • Bare-earth lidar has buildings and trees removed, so new houses or cleared forest mostly don’t show; the earthworks under them do.
  • Water surfaces, dense vegetation and steep faces are the least reliable. Treat small changes there with caution.
  • Volumes are estimates from two separate surveys, good for scale and comparison. Indicative only, not a survey.
  • Comparing on the map is free. The change GeoTIFF needs a pass. It is written on the surveys’ own 3.3 ft grid in NAD83 / UTM, and its values in the file are in meters, as USGS publishes them.
  • The before and after photos are on the map only; they are not part of the download.

Data and attribution

Heights come from each survey’s own USGS 3DEP 3.3 ft lidar DEM, fetched by your browser straight from the USGS files (cloud-optimized GeoTIFFs) and compared cell for cell with no resampling. Not the elevation tiles the other map tools read. The before and after photos are the years of aerial photos available for the area: for now only the 2021 NAIP photo, with today’s aerial basemap as the other side, shown on the map only.

USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. Tennessee parcel boundaries come from the county assessors of property, through the Comptroller’s Division of Property Assessments and county GIS offices, and are not legal surveys; the parcel disclaimer accompanies the selection. The Esri aerial basemap follows Esri’s terms and is display-only; downloadable aerial photos use USGS NAIP.

Questions

Where can I use it?

Wherever USGS publishes a 3.3 ft lidar DEM from two surveys of the same ground. In Tennessee, USGS publishes lidar DEMs from two surveys of the same ground in parts of Nashville, Memphis, Chattanooga and Jackson. Many places have only one such survey so far. Data Here shows which surveys cover a spot.

How accurate are the volumes?

Two surveys of ground that has not moved never agree exactly, so the tool ignores differences under ±1 ft. Volumes are good for scale and comparison; they are indicative only, not a survey.

Are the aerial photos in the download?

No. The before and after photos are shown on the map only. The download is the change itself, as a GeoTIFF.

Ready to try it?

Open Elevation Change on the map →

Free to use, no account. The analysis runs in your browser on public-domain USGS 3DEP data. Downloading the results needs a pass: see pricing.

Missing something you need? Suggest a feature or ask about custom work.