Before and After in Lidar: Three Places Around Chattanooga
Where the ground dropped and where it rose between two USGS lidar surveys of the same ground, measured by subtracting one from the other. Three places in Hamilton County, two in Chattanooga and one near Collegedale, each one link away on the map.
USGS publishes a 3.3 ft lidar DEM from many of the lidar surveys it holds, all on the same grid, so two surveys of the same ground line up cell for cell. Subtract the older one from the newer one and what is left is change. In Tennessee, USGS publishes lidar DEMs from two surveys of the same ground in parts of Nashville, Memphis, Chattanooga and Jackson. Many places have only one such survey so far.
All three places compare TN_27_County_QL2_LiDAR_Cumberland_Plateau_BAA, collected December 2015 to January 2016, with TN_HamiltonCounty_B25, collected April 2025, as USGS lists them over these boxes. The site takes each survey’s years from its collection dates, not its name.
On the change map, red is ground that went down and blue is ground that came up, and differences under ±1 ft are left clear as survey noise. The figures below are for a box around each place, its size given with each one, computed with the same code the map runs. What each place looks like is described from the latest USGS aerial photo of the box; on the map, the panel’s Before & after photos sets the 2021 aerial photo USGS holds there beside today’s imagery.
In Chattanooga: a quarry taken deeper
City of Chattanooga, Hamilton County · box about 0.83 mi across, 440 acres compared · surveys TN_27_County_QL2_LiDAR_Cumberland_Plateau_BAA (December 2015 to January 2016) and TN_HamiltonCounty_B25 (April 2025)
In the latest USGS aerial photo a large stone quarry fills the middle of the box: a pale floor stepped down in benches, ringed by a band of trees, with large buildings around it and a divided highway along its east side.
On the change map the whole pit is red: 6,560,875 cu yd of ground gone from 87 acres, the most ground lost in any of the three boxes, the deepest by 162 ft; the darkest red runs along the pit’s western side. Blue bands along the north rim and beyond the south-west corner of the pit, 1,190,529 cu yd raised over 54 acres, are ground built up around its edges.
Nothing here balances: far more ground left the box than was raised in it. In the later survey part of the pit floor is one dead-level surface, which is how lidar models show standing water, so there the change is measured to the water, not to the floor beneath it. In a working quarry, where faces are cut back and water can stand on the floor on the day of a flight, single extremes are the least reliable figures; trust the broad patch. The buildings and streets around it read almost entirely clear.
- Ground lowered: 6,560,875 cu yd over 87 acres, the deepest by 162 ft
- Ground raised: 1,190,529 cu yd over 54 acres, the highest by 74 ft
- Median change across the box: 0.1 ft
On the map, choose Compare this view, then Compare surveys. Before & after photos then swipes between two years of aerial photos.
In Chattanooga: a hillside cut and filled for a large building
City of Chattanooga, Hamilton County · box about 0.83 mi across, 440 acres compared · surveys TN_27_County_QL2_LiDAR_Cumberland_Plateau_BAA (December 2015 to January 2016) and TN_HamiltonCounty_B25 (April 2025)
In the latest USGS aerial photo a large building with a broad paved lot sits beside a highway interchange in the north of the box, with a smaller building near the interchange. In the south-west a bare, freshly graded site is laid out in level pads. The rest of the box is woods and homes along small roads.
The change map shows how the level ground was made. Under the building and its lot the west end is red, ground cut down by as much as 34 ft, and the east end deep blue, ground built up by as much as 32 ft. The graded site in the south-west is a patchwork of red and blue blocks. Across the box 735,399 cu yd was lowered over 52 acres and 719,237 cu yd raised over 56 acres.
Lowered and raised volumes come out almost equal, which is what cut and fill on a sloping site tends to look like: ground dug from the high end goes into the low end nearby. The homes and woods in the south and east of the box read clear.
- Ground lowered: 735,399 cu yd over 52 acres, the deepest by 34 ft
- Ground raised: 719,237 cu yd over 56 acres, the highest by 32 ft
- Median change across the box: -0.1 ft
On the map, choose Compare this view, then Compare surveys. Before & after photos then swipes between two years of aerial photos.
Near Collegedale: a hollow filled at the foot of a ridge
Hamilton County, near Collegedale · box about 0.83 mi across, 440 acres compared · surveys TN_27_County_QL2_LiDAR_Cumberland_Plateau_BAA (December 2015 to January 2016) and TN_HamiltonCounty_B25 (April 2025)
In the latest USGS aerial photo a steep wooded ridge fills most of the box. At its foot, in the south, a bare earthwork site reaches up into a hollow in the woods, with fields to its east and a road and buildings along the bottom of the box.
The change map splits the site in two. The upper part, reaching into the hollow, is blue: 792,723 cu yd raised over 27 acres, the highest by 101 ft, the highest rise of the three places. Below it, toward the road, the ground is red: 665,881 cu yd lowered over 27 acres, the deepest by 82 ft.
As at the large building, the two volumes come out close, but here the fill is piled deep in a narrow hollow rather than spread thin. The wooded ridge around the site reads clear, apart from speckle under the trees.
- Ground lowered: 665,881 cu yd over 27 acres, the deepest by 82 ft
- Ground raised: 792,723 cu yd over 27 acres, the highest by 101 ft
- Median change across the box: -0.2 ft
On the map, choose Compare this view, then Compare surveys. Before & after photos then swipes between two years of aerial photos.
Compare two surveys anywhere they overlap
Frame an area up to 1.24 mi across, or select a parcel, and compare. Free to use, no account.
Open Elevation Change →How to read a change map
- Built-up ground, such as a pad, a fill or a road embankment, shows as a patch of blue; ground cut down shows as red.
- Cut and fill on a slope shows red at the high end of a site and blue at the low end, side by side, with the two volumes close to each other.
- A working quarry shows red where rock was taken out, often deepest along one face, and sometimes blue around the rim where material was piled.
- A whole area one color can be real, or an offset between the two surveys. The panel says by how much, and names the geoid models when the surveys used different ones, as the pair here does (GEOID12B and GEOID18).
- A lake, river or flooded pit one flat color is the water standing at a different level on the two survey days, not the ground.
- Speckle under dense trees, on water and on steep faces is mostly noise. Trust broad, consistent patches.
Take it further
The change downloads as a GeoTIFF for GIS with a pass. The photos are on the map only.
Related guides
- Lidar coverage in Tennessee — which lidar project covers an address, and when it was flown.
- Lidar data for Tennessee — USGS 3DEP and the lidar surveys flown across Tennessee.
- Terrain checks before buying rural land — the checks to run on acreage before an offer.
Frequently asked questions
Can I do this for my own property?
Where USGS publishes a 3.3 ft lidar DEM from two surveys of the same ground, yes. In Tennessee, USGS publishes lidar DEMs from two surveys of the same ground in parts of Nashville, Memphis, Chattanooga and Jackson. Many places have only one such survey so far. Open Elevation Change, frame an area up to 1.24 mi across or select a parcel, and the panel lists the surveys that cover it. Data Here shows which surveys cover a spot.
How much can I trust the numbers?
Changes smaller than ±1 ft are treated as survey noise and left out. In all three boxes here the median change was 0.2 ft or less, so the two surveys agree closely on ground that did not move, even though they were processed with different geoid models. The volumes are good for scale and comparison: indicative only, not a survey.
Why does a new building or bridge not show?
The comparison uses bare-earth lidar, which has buildings, bridges and trees removed. New buildings and cleared trees mostly don’t show; the earthworks under and around them do.
Why are there no lakes or rivers here?
Lidar models show lakes, rivers and ponds as a flat water surface. Where the water stood at a different level on the two survey days, the whole surface reads as one color, which is a change in the water, not the ground. The scan that found these places counted only change on ground that was not dead level, and no lake or river lies in the three boxes. Part of the quarry floor does read as standing water in the later survey; the quarry section says so.
Will I get exactly these figures?
Only for exactly these boxes. The links open the map on each spot; the area you frame or draw there will differ a little, and so will the totals.
Can I download the change?
Comparing on the map and the before-and-after photos are free. The change itself downloads as a GeoTIFF, which needs a pass. The photos are for viewing on the map only.
About the data
Ground elevations come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model, with elevations above NAVD 88. Source cells are 3.3 ft per pixel in the finest work units, with about 9.8 ft per pixel and 33 ft per pixel sources elsewhere. USGS elevation data is public domain. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. The comparisons read each survey’s own USGS 3.3 ft lidar DEM straight from the USGS files, not the seamless model the other tools use. More from the USGS 3D Elevation Program and Tennessee elevation and lidar resources.