Water · Click a point
Where does rain from your land go? Trace it downhill
Where does water flow from your land? Click any spot in Tennessee and this tool follows rain down the ground from there, one lidar cell at a time, and draws the line it takes to the nearest stream or river.
Water & Drainage shows every flow path across an area, and Catchment shows the land draining to one point. This answers the other question: starting here, where does the water end up?
Free to run · pay to download
See the full result on the map free, with no account. Download the path as GeoJSON with a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months, a one-off payment in US dollars that never renews. Every download on the site is included while the pass lasts.
Who uses this
- Owners and buyers. See where runoff from a house site or driveway goes, and whether it crosses a property line.
- Septic and earthwork designers. Check the line and the distance from a drain field or a cut to the nearest stream.
- Farmers and ranchers. See where runoff from a barnyard or a manure area ends up, and how far it is to a stream.
When to use it
- Checking where runoff from a house site, a driveway or a new graveled pad would go.
- Seeing which way a spill, or water from a septic drain field, would travel, and how far it is to a stream.
- Working out whether water from your land crosses a neighbor’s line, a road or a building site.
Tools for your job
Downhill Path is one step in a bigger question. These are the jobs it helps with, and the tools that go with it.
For the job: Drainage, flooding and wet ground
Where does the water go, and where will it sit?
- 1.Water & Drainage — The overland flow paths across an area, sized by the land draining through them, and where water ponds once low spots fill.
- 2.Downhill Path (this tool) — Where rain from one spot ends up: the line it runs, and the stream it reaches.
- 3.Wetness Map — Which parts of a field the shape of the land keeps wet.
- 4.Catchment — All the land that drains to one culvert, draw or low corner.
- 5.Landforms — Hollows, valleys and footslopes at a glance: where water gathers.
How to use it
- Open Downhill Path and click the spot. There is nothing to set, and the path starts straight away from exactly where you clicked.
- The blue line shows where the water runs, from the orange dot to the dark dot at the end.
- Read the list in the panel: how far until the water joins a water path, becomes a watercourse or reaches a stream, and any hollows it passes through. Click anywhere else to trace from there.
Step by step: Cades Cove
We follow rain from a spot on the slopes above Cades Cove down toward the creeks on the cove floor.
1.Click the spot. The path appears straight away, and the panel lists what happens along it: how far the water runs and falls before it reaches a stream.
2.Zoom in to check the line against the aerial. Orange dots are hollows where water would pool until it overflows, and a hollow against a road usually means a culvert the terrain can’t show.
What it showed
- The line is the steepest route from one exact point. Click a few feet away on a broad slope and it can take a different line, so try more than one spot if the answer matters.
How it works
This is the Catchment calculation pointed the other way. Catchment starts at a point and walks uphill to find all the land draining to it. Downhill Path starts at a point and walks downhill to find the one line water takes away from it.
USGS 3DEP bare-earth terrain is loaded in a square 1.00 mi across, centered on your click. Small pits are filled so water can always keep moving, and each cell sends its water to its steepest downhill neighbor. From your click, the tool follows those steps one cell at a time.
When the water gets within 650 ft of the edge of the loaded terrain, the tool loads another square around where the water has got to and carries on, so the path keeps the same detail however long it gets. It stops at a stream or river draining 250 acres or more, at the edge of the state’s terrain or ground with no elevation data, or after at least 3.02 mi if neither comes first.
Reading the results
Path length is measured along the line, and drop is the height difference between your click and the end of the line.
The stages use the same classes as Water & Drainage: a water path drains at least 0.25 acre, an overland flow path 1.0 acre, a watercourse 25 acres, a stream or river 250 acres. Each is the distance at which the water first reaches that size, and the areas only count land inside the terrain loaded so far, so a stage can really begin earlier.
A hollow is a low spot on the path at least 1.5 ft deep. Water pools there until it overflows, unless a culvert or drain lets it through. A hollow against a road or embankment usually means there is a culvert the tool cannot see.
The elevation chart should fall from left to right. Flat stretches are hollows that have been filled, or water surfaces. A "Check this one" warning means the whole path has almost no fall, so it is probably on a lake, a river or very flat ground and the line can’t be relied on.
Limits and caveats
- Culverts, pipes and drains are not in the terrain, so water is routed over roads and through embankments. This is the most likely reason a path looks wrong near a road.
- It shows where water runs once it is running. Rain soaking into the ground, and how much rain it takes to get runoff started, are not modeled.
- The line is one path, but water spreads. On flat ground or a broad slope, a fraction of an inch decides the way it goes, and a click a few feet away can take a different line.
- Flat water and braided riverbeds have no clear downhill path, so the line there can wander. It does not name the stream, and it stops being useful once the water is in a river.
- Outside the finest lidar work units, 3DEP can use older lidar at about 9.8 ft per pixel or a coarser model at about 33 ft per pixel. Fine output spacing cannot recover missing source detail. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown.
Data and attribution
Results come from the USGS 3D Elevation Program (3DEP) bare-earth elevation model: lidar at 3.3 ft per pixel where it has been flown, with older lidar at about 9.8 ft per pixel and coarser sources at about 33 ft per pixel elsewhere, with elevations above NAVD 88. Every tool is bare earth: trees and buildings are not in the elevation model for Tennessee, so Sunlight, Viewshed and Sightline work from the terrain alone.
USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. Tennessee parcel boundaries come from the county assessors of property, through the Comptroller’s Division of Property Assessments and county GIS offices, and are not legal surveys; the parcel disclaimer accompanies the selection. The Esri aerial basemap follows Esri’s terms and is display-only; downloadable aerial photos use USGS NAIP.
Questions
Why does the line go straight over a road?
Culverts and pipes aren’t in the terrain, so the tool can’t see them. A hollow against a road or embankment usually means there is a culvert there, and the water really passes through it.
Does it tell me how much water, or how fast?
No. It shows the route water takes, not how much of it there is or how quickly it moves. Rainfall, infiltration and flow rates need a site assessment from an engineer.
Does it name the stream?
No. It shows the line to the stream and how much land that stream drains at that point, but it does not have the name.
Ready to try it?
Open Downhill Path on the map →Free to use, no account. The analysis runs in your browser on public-domain USGS 3DEP data. Downloading the results needs a pass: see pricing.
Missing something you need? Suggest a feature or ask about custom work.