Elevation profiles for hiking in Tennessee

Distance tells you how far; the profile tells you how hard. Draw any trail in Tennessee and see its climb, descent and high point in feet, read from USGS 3DEP lidar.

Profile your next hike

Tap out the trail on the map and get total climb, descent and the high point. Free, no account.

Open Elevation Profile →

Why elevation profiles matter for hiking

Two trails of the same length can be completely different days. A walk on the flat bottomland around Reelfoot Lake and a climb up Mount LeConte might cover similar distances, but the second one gains most of its height in a short, steep stretch. The profile shows that before you lace up.

  • Effort: total climb, not distance, is what tires most hikers.
  • Time: climbing slows everyone down, and steep descents do too.
  • Where the hard part is: one long climb at the start, a steady grind or a steep finish to a summit each call for a different plan.
  • Exposure: the high point tells you how far up onto open ridges, balds and bluff edges, and into the wind and weather, the route goes.

Made for Tennessee trails

Tennessee hiking runs from the high, forested peaks of the Great Smoky Mountains and the grassy balds of Roan Mountain to the gorges and waterfalls of the Cumberland Plateau, the hollows of the Highland Rim and the bluffs above the Mississippi River. Under the hardwood canopy of the mountains, GPS altitude is at its worst. The bare-earth lidar model reads the forest floor, so the profile shows the ground you walk on rather than the treetops.

How to create a hiking elevation profile

  1. Open Elevation Profile and search for the trailhead or the peak.
  2. Switch to the USGS Topo basemap to see the trail.
  3. Tap along the trail from the trailhead, with points close together on switchbacks.
  4. Finish the line and read the chart and the figures.

A line can be up to 15.5 miles long. For the full walkthrough, see how to create an elevation profile.

Understanding your hiking profile

Key figures for hikers

  • Total climb: the best single measure of how hard the hike is.
  • Total descent: the knees’ share. A long descent on a steep trail is hard work in its own right.
  • High point: where the weather and wind will be worst, with the least shade.
  • Range: high point minus low point, the biggest single climb.

Reading the chart

Look for where the line is steepest: that is where you will slow down most. A route that climbs steadily is easier to pace than one with a steep wall in the middle. On an out-and-back, remember that the climb on the way in is the descent on the way out.

Tennessee trails to profile

Long trails, a day at a time

The Cumberland Trail, a long, narrow state park across the Cumberland Plateau, is far longer than one line, so draw it day by day. Profiling each day’s stretch shows where the gorge crossings and climbs back onto the plateau fall, so you can balance the days.

Regional favorites

  • Mount LeConte: the trails up this massive peak in the Great Smoky Mountains climb long and steadily from the valleys near Gatlinburg; a profile shows where the steepest stretches fall.
  • Clingmans Dome (Kuwohi): the highest summit in the Great Smoky Mountains, on the crest along the Tennessee and North Carolina line; the high point matters for cold, wind and weather.
  • Roan Mountain: trails along the crest cross open grassy balds, with steep forested slopes falling away on both sides.
  • Fall Creek Falls: trails run along the rim of the gorge and drop toward the base of the falls; draw them closely where the path switches back down the gorge wall.
  • Lookout Mountain: trails above Chattanooga climb the steep flanks below the sandstone cliffs, so the climbing comes in short, hard pitches.

Planning a hike with the profile

Estimating hiking time

A common rule of thumb hikers use, Naismith’s rule, allows one hour per 3 miles plus one hour per 2,000 ft of climb. It is a planning aid, not something the tool calculates. Treat it as a starting point and adjust for your own pace, the trail surface, a heavy pack and the descent.

Backpacking trips

Draw each day as its own line. Days with a similar climb are easier to manage than one huge day followed by an easy one, and the profile shows where a camp on a bench or a saddle would split the climbing well.

Gear and preparation

The high point decides how much warm and waterproof gear you carry, and in the summer heat the length of the climbs decides how much water you need. A long, steep descent is a reason to bring trekking poles.

Safety

  • Check the weather for the high point, not just the trailhead.
  • Plan a turnaround time, and know where the profile lets you bail out early.
  • Carry water for the climbs; the profile shows how long they last.
  • The profile is the bare ground. It does not show flooded crossings, washouts, closures or trail conditions; check with the land manager before you go.

Know the climb before you go

Draw the trail and get the profile in seconds. Free, no account, nothing to install.

Data quality for hiking

Ground elevations come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model, with elevations above NAVD 88. Source cells are 3.3 ft per pixel in the finest work units, with about 9.8 ft per pixel and 33 ft per pixel sources elsewhere. USGS elevation data is public domain. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. The model is bare earth: footbridges show as a dip to the creek below. See the lidar coverage guide for how to check a place. More from the USGS 3D Elevation Program and Tennessee elevation and lidar resources.

Frequently asked questions

How accurate are the hiking profiles?

The elevations come from the USGS 3DEP bare-earth model, 3.3 ft per pixel where the lidar meets the USGS standard for its finest DEM, and coarser elsewhere. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. Lidar reaches the ground under the trees, so forest trails are profiled at ground level. The biggest source of error is usually the line itself: follow the trail closely, especially on switchbacks.

Can I profile a trail that is not in a trail database?

Yes. You draw the line yourself, so any trail, abandoned road or off-trail route you can trace on the map works. The USGS Topo and aerial basemaps help you find the line.

How much climb is a lot for a day hike?

It depends on your fitness, the trail and the weather, so there is no single number. Compare the climb on a new trail with hikes you already know: if a familiar hike felt hard, a new one with more climb in the same distance will feel harder.

Can I download or share my profile?

Yes. Save chart image under the profile saves a free picture of the chart, and Save image in the map menu a free PNG of the map view. With a pass, the profile downloads as CSV, GeoJSON, KML or DXF. To put lidar elevations into a GPX track for your own app, use Elevate a File, which needs a pass to run.

Can this help me train for a specific hike?

Yes. Profile the hike you are aiming for, then profile local training hikes and pick ones with a similar climb per mile. Build up the total climb you do in a week toward what the target hike asks for in a day.

Related guides