Elevation profiles for cycling in Tennessee

On a bike, grade is everything. Draw a road or gravel ride anywhere in Tennessee and see where it climbs, how steep and for how long, read from USGS 3DEP lidar.

Profile your ride

Tap out the route on the map and read the climbs. Free, no account.

Open Elevation Profile →

Why elevation profiles matter for cycling

Cyclists feel grade more than almost anyone: the power needed to hold a speed rises steeply as the road tilts up. A profile shows where the climbs are, how long they last and how steep they get, so you can choose a route, gearing and pacing before you start.

  • Route choice: compare two ways over the same hills.
  • Effort: total climb and the steepest sustained section decide how hard the day is.
  • Fueling: eat before the long climbs, not on them.
  • Safety: know where the fast descents are before you reach them.

For every kind of riding

Road: farm-country loops in the Nashville Basin and long climbs onto the Cumberland Plateau. Gravel:county roads on the Highland Rim and forest roads in the mountains of East Tennessee, where grades change quickly. Touring and bikepacking: multi-day routes split into daily stages. Commuting: find the gentlest way across town.

How to create a cycling elevation profile

  1. Open Elevation Profile and find the start of the ride.
  2. Tap along the road, with more points on hairpins and bends.
  3. Finish the line and read the chart, total climb and descent.

A line can be up to 15.5 miles long, so profile a longer ride in sections, for example one per climb.

Understanding your cycling profile

Key figures for cyclists

  • Total climb and descent in feet.
  • Climb per mile: total climb divided by length, to compare rides of different lengths.
  • Grade: elevation change over distance in percent. A 6% grade climbs 6 ft every 100 ft, or about 317 ft in a mile.
  • High point: where the descent starts, and where wind and sun are strongest.

Sizing up a climb

A climb’s difficulty comes from its length and its grade together. To size one up, draw a line from its foot to its top: the climb divided by the length gives the average grade, and the steepest part of the chart shows where it kicks up.

Reading the profile for pacing

Start long climbs at an effort you can hold to the top. Use the flats and descents to eat, drink and recover. On rolling terrain, the profile shows whether momentum will carry you over the next rise.

Tennessee rides to profile

Ridges, rims and the plateau

In the Ridge and Valley of East Tennessee, roads either follow a valley floor or cross a long ridge in one steep climb. On the Highland Rim, roads climb out of one creek hollow and drop into the next, so a ride stacks up many short, steep climbs. Where a road climbs the Cumberland Plateau escarpment, the climbing comes all at once. Draw each climb as its own line.

Basin and plains

The farm roads of the Nashville Basin roll gently, and the loess plains and the Mississippi River lowlands of West Tennessee are some of the flattest riding in the state, where wind matters more than climb. Where a road climbs the bluffs above the river, the climbing comes in one short pitch.

Rail trails

Rail trails follow old railroad grades, so they climb gently even through hilly country. A profile shows where a trail’s gentle grade ends and the roads that link it begin to climb.

Training with power and climbs

Planning target efforts

If you train with power, use the length and grade of a climb from the profile to decide what effort you can sustain to the top, based on climbs you have ridden before.

Structured training

Find a local climb whose grade and length match a target event and use it for repeats.

Looking back

After a ride, compare your recorded climb with the lidar profile of the same route. A big gap usually points to the bike computer’s altimeter, not the road.

Gearing

Gearing is about the steepest climbs you will meet, especially late in a long ride. Check the profile for steep sections and choose lower gears if you are unsure.

Ride time

Climbing slows everyone down, and the descent does not give it all back. Estimate ride time from rides you know with a similar climb per mile, not from flat-road speed.

Food and water

Plan to eat and refill before long climbs and at the top, and carry more on rides where the profile shows long climbs far from towns.

Safety

  • Know where the long, fast descents are and check your brakes before them.
  • Bring a layer for long descents; the wind chill builds quickly on the way down.
  • Low-water crossings on rural roads can flood after heavy rain, and some trails close after wet weather; the profile does not show road or trail status, so check before you go.

See the climbs before you clip in

Draw any ride in Tennessee and read its profile in seconds. Free, no account.

Bike computers and apps

To replace the altitude in a recorded ride with lidar ground elevations, upload the GPX to Elevate a File (it needs a pass, asked for before the upload) and import the new file into your app. See adding elevation to GPX files.

Data quality for cycling

Ground elevations come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model, with elevations above NAVD 88. Source cells are 3.3 ft per pixel in the finest work units, with about 9.8 ft per pixel and 33 ft per pixel sources elsewhere. USGS elevation data is public domain. Lidar coverage and source dates vary across Tennessee. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. Because the model is the ground with no structures, a road bridge shows as a dip to the river below and a tunnel as the hill above it. Draw around them, or allow for them when you read the climb. More from the USGS 3D Elevation Program and Tennessee elevation and lidar resources.

Frequently asked questions

How much climb makes a century ride hard?

It depends on the rider, the grades and the weather, so there is no single number. Profile rides you already know and use them as a scale: a new route with clearly more climb per mile than your usual rides will be a harder day.

How do I know what gearing I need?

Look for the steepest sustained section of the route on the profile, not the average. If you struggle on a familiar climb of similar grade and length, choose lower gears for the new one. A bike shop can help match gearing to the grades you expect.

Can GPS bike computers measure elevation accurately?

Many use a barometric altimeter, which tracks changes well over short periods but drifts with the weather; others rely on GPS altitude, which is noisy. Both can over- or under-count total climb. The profile here reads the ground from the USGS 3DEP lidar model instead.

How much should I slow down on climbs?

Ride climbs by effort, not speed. Your speed will drop with the grade; the profile shows how long each climb lasts, so you can choose an effort you can hold to the top.

Can I use this for indoor training?

You can use the profile to plan a session: note the length and grade of a climb you want to simulate and set your trainer or workout to match. Hover along the chart to read the gradient at each point; with a pass, the profile downloads as a CSV with the distance, elevation and gradient of every point.

Related guides